Essays on Flow Rate

Abstract

The document considers the use and conservation of energy in domestic dwellings using heating systems, specifically water heated boilers, which is the cheapest solution in the market for home heating systems in Ireland and Europe. The document starts with a literature review of the available home heating systems and focuses on boilers due to its availability and price. The literature review includes a standard boiler array for a typical house, the radiators materials, and key concepts to understand the use of boilers for heat generation in homes. Later, it is necessary the calculation of heat transference for a given ...

Q1. A 200mm diameter pipeline divides into two smaller pipelines, one being 100mm in diameter and the other being 150mm in diameter. If the velocity in the 100mm pipe is 0.3m/s and that in the 150mm is 0.6m/s, calculate the flowrate in litres/s and the velocity in m/s in the 200mm pipe. [ 13 l/s, 0.413m/s] Solution: Flow Rate = (pi/4)(0.1)2(0.3) + (pi/4)(0.15)2(0.6) = 0.01296 cubicmeters/sec = 12.96 l/sec. (ans.). Velocity = (Flow Rate)/(Area) = [0.01296]/[(pi/4)(0.1)2] = 0.4125 m/s. Q2. If the specific volume of water is 0.001251 m3 /kg. calculate:

The mass and weight ...

Single Pump Results

Single Pump Calculations

Impeller Diameter (D) 114mm

Venturi inlet diameter (AP) 27.2mm Venturi throat diameter (AT) 18.5mm All calculations done assuming ρ= 1000 kg/m3 1. Graphs for the single pump test Figure 3: Percentage efficiency plotted against the flow rate in litres per second 2. Analysis of single pump graphs The graph in Figure 1 demonstrates an inverse correction that exists between flow rate and the size of the head. According to the curve, the fluid flow exhibits a maximum head (16.20795m) at zero flow (Derakhshan and Ahmad 807). On the other hand, the fluid flow demonstrates a minimum head (4.99490m) at the moment ...

Abstract

The experiment was done to investigate the relative roughness of pipe three though a plot of the friction factor verses the Reynolds number. A comparison of the obtain results was made against a Moody diagram. Also, additional comparison of the experimental results obtained from pipe 1 and 2 were made against theoretical values obtained through Prandtl and Blasius equations. This process entailed plotting the theoretical and the experimental values on the same comparative roughness against Reynolds number chart. Additional results of different types of flow, exhibited by the flowing fluid, was done and represented in a graph of head ...

An Assignment Submitted by

Asthma is a disease affecting the lungs. Because of asthma the lung tissues become inflamed and narrowed, and this influences the breathing process of the patient. They feel chest tightness, shortness of breath, wheezing and coughing at night or at early morning. Usually the symptoms of chronic asthma are being observed from childhood, but the disease can affect all age groups and reveal itself in adulthood as well. Asthma is a long-term disease. In most of the cases the inflamed airways react to a specific allergen coming from the environment such as pollen, dust or smoke. In order to ...

Introduction

In the adsorption-membrane hybrid system for ethanol steam reforming: Thermodynamics analysis by Dang, Amornchai, Yaneeporn, and Suttichai, (2011, International Journal of Hydrogen Energy), the authors seek to explain how an adsorption-membrane hybrid system, which uses a carbon (IV) oxide as an adsorbent can be used to eliminate unwanted carbon (IV) oxide in the hydrogen separation process. The authors aimed at improving the ethanol steam reforming performance through comparison of thermodynamic analysis that comprised of adsorptive, as well as membrane reactor. Then the authors were able to find that membrane separation process for the hydrogen removal had a higher impact ...

Improvement in fire suppression systems has been the focus of not only the construction industry but also by fire risk management agencies (Liu and Kim, 1999, p.32). This is the reason why experimental and computational modeling studies were used by Liu and Kim (1999, p.32) to not only validate fire tests but to improve the effectiveness and efficiency of fire suppression systems. Computing for water spray characteristics includes ventilation conditions of the area, droplet size, and flux density (Liu and Kim, 1999, p.32). The purpose of which is to improve fire suppression strategies especially in different fire scenarios (Liu ...

Introduction

The experiment was conducted to examine the validity of Bernoulli’s Principle as applied to the flow of water in a tapering circular duct. It employed the use of Bernoulli’s Theorem Demonstration Apparatus, hydraulics bench and a stopwatch to gather relevant data. The volume of water was measured and its flow was timed using the stopwatch. The two values were used to calculate the flow rate of the fluid. Additionally, the manometer readings were collected and used to compute the velocity of the fluid at each tapping position. The values were used to calculate the theoretical velocity head ...

Introduction

The experiment was conducted to establish the association between head loss as a result of fluid friction and the flow rate of water. Turbulent and laminar flow within the pipe were also investigated. Fluid Friction Equipment containing three bore pipes was used to take the data of head loss at dissimilar velocities. Different readings on volume, time, flow rate, pipe diameter, and velocity and head loss of both mercury and water were collected. The data collected were used to investigate the association between head loss due to friction and the flow rate of water through bore pipes. An estimate ...

Introduction

The main objectives of this report include; designing the operational principles of parallel and counter flow of heat exchangers. Improving the understanding of fluid temperature and flow rate heat exchangers and lastly to calculate and determine the overall heat transfer coefficient of a heat exchanger ("Superplastic duplex stainless steel heads for the heat exchanger market", 2010). The parallel flow of fluid is characterized by the flow of cold and hot fluids in the same direction; it, therefore, means that the entrance for the two fluids are in the same direction likewise their exit are also normally in the same ...

Introduction

The flow of a given volume of fluid through a pipe requires a given amount of energy. In order for fluid flow to occur, there must be pressure or energy difference. During fluid flow through a pipe, energy is lost. The main causes of this loss are the resistance encountered by the fluid in the process of its movement through the pipe. Viscosity is one of the most common forms of resistance to fluid flow through a pipe (Noltingk, 1985, p. 5). Fluids that have high viscosity tend to exhibit high resistance while flowing through a pipe (Considine and ...

Introduction

At times, industries require the temperatures to be kept below the ambient for some processes to be effective. To do so, they must design ways to eliminate the excess heat generated by machines and introduce an artificial room temperature lower than the ambient. They must effectively eliminate temperatures above the ambient. A refrigerator is thus required in these operations. This refers to a device that can maintain the temperature below the ambient. The primary objective of a refrigeration process is to lower the temperature through heat removal. Since its invention, refrigeration has seen used in many industrial and household ...

Lab Report

Lab Report

Introduction

Air stripping lacks an official academic definition, but a widely accepted definition within the field regards it as the transfer of contaminants from aqueous solutions to air [1]. This process is commonly performed to decontaminate waste water and groundwater for public health purposes, given its ample use in the removal of volatile organic compounds (VOCs) from water into air. Air strippers, the devices that carry out this process, are composed of a cylindrical tank which can contain different materials such as steel, ceramic or plastic. Contaminated water is pumped into the apparatus through its upper inlet, proceeds ...

Introduction

A refrigerator is an electrical device used in temperature maintenance below ambient temperatures. To achieve this function, the refrigerator should be able to create a heat sink at cold room temperatures a temperature that should be lower than the ambient temperature while at the same time also rejecting heats having higher temperatures than the ambient temperatures. To achieve this refrigerant is forced to undergo evaporation at temperatures lower than the ambient temperature(Griffiths, 1937). When the refrigerant is compressed at high pressure and condensing temperatures above the ambient temperature results in the loss of heat and condensation back to ...

My Name

Shell and Tube Heat Exchanger Lab Report Objectives Introduction A heat exchanger refers to a gadget that aids the transfer of heat from one fluid to another. The fluids involved can either be in direct contact or separated to avoid mixing (Ramesh & Sekulic, 2003). They are in common use in sewage treatment, natural gas processing, petroleum refineries, petrochemical plants, chemical plants, power stations, air conditioning, refrigeration, and space heating. A perfect example of a heat exchanger is in the internal combustion engine (ICE) (Hiereth & Prenninger, 2010). In such a situation, a circulating fluid called engine cooler flows over the ...

BERNOULLI’S EXPERIMENT

ABSTRACT Two fluid properties, the Bernoulli principle and the Venturi effect, were examined and analyzed in this experiment. A venturi meter was used to measure the fluid flow rate, velocity, and pressure of water (the fluid being examined). The results showed that the fluid pressure decreases as the fluid traveled through a smaller cross sectional area. The minimum fluid pressure (in effect, maximum fluid velocity) was observed in the smallest cross sectional area at position D (diameter 16 mm). The decrease in fluid pressure was compensated by an increase in the fluid velocity. With these two measured phenomena, both ...

BERNOULLI’S EXPERIMENT

INTRODUCTION This experiment aims to verify Bernoulli’s equation that relates the pressure and the velocity of a fluid. The aims of the experiment are: A venturi meter is a device used in fluid measurements. It uses a converging section of a pipe in order to change fluid velocity or pressure. The venturi meter in this experiment is used several times to estimate flow rates and measure piezometric head values at different points along the venturi meter. The fluid used in this experiment is water. Bernoulli’s equation is a mathematical model for ideal fluids. Because of this, the ...

Objectives

Introduction A wind instrument is an instrument that produces sound by manipulating air through varying the wind pressure passing through the air outputs of the device (Berg and Stock, 27). These devices are heavily dependent on pressure as well as the size and shape of the instrument (pg. 28). A good example of a wind instrument is the organ pipe. It is a tool that produces a specific pitch when pressurized air is driven through it. Organ pipes usually exist in sets, where each is confined to produce a specific tune. Normally, it is a keyboard device that is ...

Re: A column to separate an Acetone-Methanol mixture

The objective of the project was to optimize the design of a column used to process a supply stream containing 35 percent acetone at 30oC. The optimized design should turn out a distillate product containing 0.75 mole fraction of acetone and 0.0010 fraction of bottoms acetone. The outcome of the experiment produced a distillate product containing 0.0079 molar fraction of acetone.

The molar fraction of acetone in the first inlet stream was determined to be 0.14 lbmol/min. Also, the total flow rate of the second inlet stream and the total gas flow rate were determined to be 61.84 lbmoles/min ...

Aims

Studying the vibrational modes of organ pipes Introduction Sound is a vibration that arises from a mechanical wave of pressure and displacement, through a medium like air or water (Berg and Stock, 23). The reception and perception of these waves by the brain is referred to as sound. On the other hand, acoustics deals with the study of these mechanical waves in matter (pg. 40). In this experiment, the organ pipe is the main target of discussion. This is a sound producing wind instrument that resonates at a specific pitch when pressurized air is driven through it. A complete ...

Pump Application: Building Water Pump

Pumps are devices used to move fluids from one point to another by creating differences in pressure between the two points. Pumps are powered by a prime mover, which can be either a diesel engine or an electric motor. The pump converts the energy supplied by the prime mover to potential energy by pressurizing the fluid it’s pumping. For example, a diesel pump has an engine that converts chemical energy in the fuel to mechanical energy in the form of torque. The torque from the engine is then picked up and transmitted to the pumping mechanism for fluid ...